 |
DMD Insulator
These
are perfect replacements for the Dot Matrix Display insulator
covers installed on DMD equipped pins. Made of heavy fish
paper insulator sheet and cut to fit the back of all standard
192 x 64 Cherry, Babcock, and Vishay Dot Matrix Displays.
Protects the user and the other boards from the high voltage
present on a DMD.
$10.00
each
|
|
|
Twilight
Zone Mini Playfield Insulator
These are perfect replacements for the
insulator covers installed under Twilight Zone's mini
playfield. Made from heavy fish paper insulator sheet,
just like the original. Protects the magnets and electrical
connections from damage and shorts due to pinball
contact.
$15.00
each
|
|
|
Plastic Tack Glides
These are exact replacements for the
glides that are usually installed on the back of machines to
protect them when sitting folded in storage. Sometimes seen on
the bottom of the head as well. Brown or white plastic 3/4"
diameter with a nail embedded. Pack of 4.
$1.00 per pack of
4
|
|
|
Flange Nuts with
Integral Lockwasher 1/4-20
These
are the nuts used in various places around the cabinet,
usually on 1/4-20 carriage bolts. A combination of a nut and
a lockwasher. Bright Zinc plated. Pack of
8.
$1.00 per pack of
8
|
|
|
Side Rail Carriage Bolts 8-32 by
1"
These
are zinc plated carriage bolts that are an excellent
replacement for the side rail bolts on many machines. They
have a clean head with no lettering. The factory bolts were
slightly longer, about 2 threads, but these will work
fine.
$.25
each
|
|
|
Black Carriage Bolts
These
are black oxide finish carriage bolts that are used on
many machines. They have a clean head with minimal
lettering. They are used on the coin door, in the head, and
some other spots where brackets are bolted to the cabinet.
Available in 2 sizes, 1-1/4" and 1-1/2" long. The shorter ones
are common in and around the coin door, longer ones are
usually in the head. Pack of 4.
$1.00 per pack of
4
|
|
|
Black Screws for Backbox Lock Plate
These
are black oxide finished 8-32 Phillips Head
machine screws. These are handy replacements for the
button Torx security screws initially used by the factory in
the backbox lock plate. Pack of 4.
$1.00 per pack of
4
|
|
|
Socket Head Screws for Capcom Flipper
Stops
These
are black oxide finished 1/4-20 Socket Head
machine screws with the correct narrow split ring
lockwashers. These are handy replacements for the
Capcom flipper stop screws which often get damaged in
disassembly. Pack of 4 screw and washer
sets.
$1.00 per pack of 4
sets
|
|
|
Socket Head Set Screws 1/4-20
These
are black oxide finished 1/4-20 Socket
Head set screws with a knurled tip. These are used
on many games to tighten a lever, gate, or other assembly onto
a shaft. They often get rounded out or crack making it
impossible to tighten. 1/4" in length with a 1/8" hex (allen)
socket. Pack of 4.
$1.00 per pack of
4
|
|
|
Twilight Zone
Clock Board Spacer Kit
These are screw
and spacer kits to replace the usually cooked and broken
plastic standoffs between TZ's clock boards. The kit includes
4 screws, 4 locknuts, and 4 nylon spacers. Enough hardware to
fix 1 TZ clock while maintaining the correct spacing
between the boards. Also helps with intermittent connections
by holding the boards in a stable orientation.
$2.00 per
kit
|
|
|
Nylon Screws 8-32 pack of
2
These are white
Nylon screws that are great replacements for the AFM Saucer
screws.
$.50 per pack of
2
|
|
|
Push Nuts for
WPC-95 DMD Panel
These are exact
replacements for the steel push nuts used by the factory.
They're used to hold the DMD plastic panel and speaker grilles
on the WPC-95 games. These nuts were never designed to be
re-used and often get wrecked in disassembly. Package of
6.
$1.00 per pack of
6
|
|
|
Slingshot Arm
Washers for WPC Pins
These are exact
replacements for the spacer washers used on the slingshot
kicker arm. Made of stainless steel. Also used on the kickout
lever. Replaces Williams Part # 4700-00030-00.
Package of 6.
$1.00 per pack of
6
|
|
|
Drop Target Washers
These are exact
replacements for the washers used on Williams drop targets.
Thin washers with a 17/64" ID and a 1/2" OD to fit in the
channel molded into Williams style flat drop target
assemblies. Made of stainless steel. Replaces Williams
Part # 4700-00072-00. Package of
6.
$1.00 per pack of
6
|
|
|
Shooter Washers
These are exact
replacements for the ball shooter rod washers except in
stainless steel for lasting beauty. The original part is a
zinc-plated mild steel and the plating wears off easily, often
getting rusty from hand salts. The picture shows an
original shooter washer on the left and my stainless
steel replacement on the right. Replaces Williams
part # 4700-0051-00. Package of
4.
$1.00 per pack of
4
|
|
|
Lightboard Hinge Washers
These
are reasonable replacements for the shimming washers used
to adjust the height of the lightboard hinge in Wms DMD games.
These are the same ID and thickness as the originals but are
slightly smaller in OD. Made of stainless
steel rather than zinc-plated mild steel. Stop your lightboard
from dragging on the latch bracket. Package of
3.
$1.00 per pack of
3
|
|
|
T-nuts
These are used
under the playfield to anchor posts and other parts. 6-32 thread, base
size .56". 8-32 thread, regular base size .59", large base
size of .71", small base size of .50". 10-32 thread, base
size .75". Package of 8.
$1.00 per pack of
8
|
|
|
ESNA (Lock) Nuts
These are used
throughout pins, both modern and classic. The color of the
plastic inserts may vary, depending on the manufacturing
batch. Three common sizes, 6-32, 8-32, and
10-32. Package of
8.
$1.00 per pack of
8
|
|
|
ESNA Jam Nuts
These are thinner
versions of the standard ESNA nuts. Many times this type
is used by the factory. Also useful for adding Lexan washers
or plastics protectors as the thinner nut will still bite into
the nylon lock area, even with a thicker plastic below
it. These are the nuts shown in front of the standard
sizes in the pic. Three common sizes, 6-32, 8-32, and
10-32. Package of
8.
$1.00 per pack of
8
|
|
|
KEP (Lockwasher) Nuts
These are used
throughout pins, both modern and classic. Three common sizes,
6-32, 8-32, and 10-32. Package of
8.
$1.00 per pack of
8
|
|
|
SEMS (Lockwasher) Screws 6-32
These are used
throughout pins, both modern and classic. Four common
lengths, 1/4", 3/8", 1/2", and
3/4". Package of 8.
$1.00 per pack of
8
|
|
|
SEMS (Lockwasher) Screws 8-32
These are used
throughout pins, both modern and classic. Four common
lengths, 1/4", 3/8", 1/2", and
3/4". Package of 8.
$1.00 per pack of
8
|
|
|
SEMS (Lockwasher) Screws 10-32
These are used
throughout pins, both modern and classic. Two common lengths,
3/8" and 1/2". Package of
8.
$1.00 per pack of
8
|
|
 
|
Small Machine Screws
These are used in
many places in pins old and new. Two common
sizes, 4-40 x 1/2" and 2-56 x 3/4". The smallest
2-56 screws are shown in the top picture, they are often used
to hold switch stacks together. The set includes 2 each of a
3/4" screw, flat washer, lock washer, and hex nut. The
larger 4-40 screws are shown in the bottom picture and
includes 2 each of a 1/2" screw and ESNA lock nut. These
can also be easily trimmed down to a shorter length with our
Diagonal Cutters. Tip: When cutting
screws, first thread a nut on the screw above where you're
going to cut. Cut the screw to length. Then, as you
remove the nut, it will straighten out the cut threads as it
comes off the screw. Package of 2
sets. (Pennies not included ;)
$.50 per pack of 2
sets
|
|
 
|
Long Machine Screws, Phillips
Head
These are used in
many places on the playfield to hold plastic posts
down. Usually, they screw into a t-nut. These are zinc
plated steel machine screws. Two common
sizes, 6-32 x 1-1/4" and 8-32 x 1-3/4". These can also be
easily trimmed down to a shorter length with our Diagonal Cutters. Tip:
When cutting screws, first thread a nut on the screw above
where you're going to cut. Cut the screw to length. Then,
as you remove the nut, it will straighten out the cut threads
as it comes off the screw. Package of
4.
$1.00 per pack of
4
|
|
|
Very Long Machine
Screws, Phillips Head
These
are often used on the playfield
to attach plastic lane guides. Usually, they screw
into a t-nut. These are 6-32 zinc plated steel
machine screws in a 2-1/2" length. These can also be
easily trimmed down to a shorter length with our Diagonal
Cutters. Tip:
When cutting screws, first thread a nut on the screw above
where you're going to cut. Cut the screw to length. Then,
as you remove the nut, it will straighten out the cut threads
as it comes off the screw. Package of 4
$1.00 per pack of
4
|
|
|
Very Long Machine Screws, Hex
Head
These
are often used on the playfield to
hold machinery down. Usually, they screw into a t-nut.
These are 8-32 zinc plated steel machine screws in a
3" length. These
can also be easily trimmed down to a shorter length with our
Diagonal
Cutters. Tip: When
cutting screws, first thread a nut on the screw above where
you're going to cut. Cut the screw to length. Then, as
you remove the nut, it will straighten out the cut threads as
it comes off the screw.
$0.25
each
|
|
  |
Long Wood
Screws, Phillips Head
These are used in
many places on the playfield to hold plastic posts
down. Usually, they screw directly into the wooden playfield.
These are zinc plated steel wood screws. Two common
sizes, #8 x 1-1/2" and #8 x
1-3/4". Package of 4.
$1.00 per pack of
4
|
|
|
Self-Tapping Screws, Hex Head, Stainless
Steel
These are used all
over the underside of the playfield
to mount assemblies. These are unslotted #6
screws made of stainless steel. Four common
lengths, 3/8", 1/2", 5/8", and 3/4". The 5/8" and 3/4"
sizes are used only where there is no danger of the screw
popping up through the playfield! Usually to hold a thick
bracket or part to the
playfield. Package of
8.
$1.00 per pack of
8
|
|
|
Self-Tapping Screws, Hex
Head, Zinc-Plated Steel
These are used all
over the underside of the playfield
to mount assemblies. These are unslotted #6
screws made of regular steel with a zinc-plated finish. Available only
in 1/2" length. Package of
8.
$.50 per pack of
8
|
|
|
Self-Drilling Screws, pack of 6
These are self-drilling
screws with a phillips head. They are 5/8" long and commonly used to hold the
DMD to the plastic bezel in a WPC-95 game. Will also
work for the speakers in a WPC-95 game. Package
of 6.
$1.00 per pack of
6
|
|
|
Flat Head Screws, pack of
2
These are flat head wood
screws in 2 sizes. The 1/2" screw fits plastic ramp flap areas
where the ramp is screwed to the playfield. The 3/4" screw is
perfect for inside pop bumper bodies to screw them down to the
playfield. Comes in packs of 2.
$.25 per pack of 2
|
|
|
Brass Screw w/ Brass Washer 8-32
These are used to attach
solid-core coils to their steel brackets. Brass screw and
washer won't magnetize. Used on EM relay coils as well as
modern gate coils and other assemblies with solid-core
coils. 8-32
screw 3/8" long and a #8 brass washer 7/16" OD. Also
includes 2 #8 split lockwashers in steel.
Package of 2 screws, 2 flat washers, and 2
lock washers.
$1.00 per pack of
2
|
 |
E-Clips
These are used in many
applications on pins of all ages. Available in 7 sizes:
7/16", 3/8", 5/16" 1/4", 3/16", 5/32", 1/8". Also
available is the 1/4" "Poodle Head" clip as used by Bally
shown on the bottom in the pic. Packs of 8 clips
each.
Pack of
8
|
|
|
Hairpin Clips
These are used
to secure slingshot kicker arms as well as other
applications. Zinc-plated spring wire clips for 3/16" shafts.
Replacement for
Williams part # 12-6227. Also fits Williams EM flipper links.
Package of 8.
$1.00 per pack of
8
|
|
|
PC Board Grommets
These are used to attach
printed circuit boards to a multiple drop target assembly. Replaces
Williams Part # 23-6626. Package
of 4.
$1.00 per pack of
4
|
|
|
Solder Lugs
These are used to attach
wiring to the ground braid. Also found under the playfield in some lamp
wiring. Two different types; Angled with lockwasher or
Straight. Package of 8.
$1.00 per pack of
8
|
|
|
Cage Nuts 8-32
These are used
to secure the wire fence to the lower arch. Replacement for
Williams part # 20-9601.
$.50
each
|
|
 |
Apron Screws & Speed Nuts - Set of 2
each
These are used
to secure the lower apron or arch to the playfield
hanger brackets. Replacement for Williams part # 20-9041.
Package of 2 speed nuts and 2
screws.
$1.50 per set of 2 of
each
|
|
|
Service Cord 1'
These are used to tap
power for servicing WPC-95 games. Plug in your
soldering iron or light. IEC modular male to standard NEMA
female.18 gauge wire with molded
ends.
$3.00
each
|
|
|
Power Cord 10'
These are nice, long
versions of the standard power cord supplied with modern
games. 10 feet with an IEC modular female plug. Also great for
rewiring older games with a nice, long cord. Just cut off the
modular end and strip. 18 gauge wire
with molded ends, grounded.
$4.50
each
|
|
|
Power Cord 15'
These are nice, longer
versions of the standard power cord supplied with modern
games. 15 feet with an IEC modular female plug. Also great for
rewiring older games with a nice, long cord. Just cut off the
modular end and strip. 18 gauge wire
with molded ends, grounded.
$6.50
each
|
